TRA1747 Nuts, 4mm nylon locking (10)
TRAXXAS
Nuts, 4mm nylon locking (10) Set of ten 4 mm Nylon locking nuts Replacement part for these models: Bandit® VXL Bandit® BIGFOOT® No. 1 Officially...
View full detailsNuts, 4mm nylon locking (10) Set of ten 4 mm Nylon locking nuts Replacement part for these models: Bandit® VXL Bandit® BIGFOOT® No. 1 Officially...
View full detailsTraxxas X-Maxx Rear Body Support. Package includes replacement rear body support and hardware. Includes: Rear body Support (2) 3x15mm CS (2) 3x1...
View full detailsTraxxas Cush Drive Housing. Package includes one front half and one rear half. Features:Nylon Construction Includes:(1) Front Half(1) Rear Half
Nuts, 4mm flanged nylon locking (aluminum, pink anodized) (4) Lightweight and great looking, these 4 mm anodized aluminum flanged lock nuts are th...
View full detailsThis is the input shaft for use on the Traxxas Slash 4x4 vehicles.Features: Steel construction that is black in colorIncludes: Input Shaft Bearing...
View full detailsTRA5459 Revo T-Maxx Rubber Driveshaft Boots(2) Boots, driveshaft (rubber) (2) Replacement part for these models: E-Revo Brushless E-Revo Revo T-Maxx
These are the optional 17mm splined wheel hubs for the T-Maxx 3.3 4WD Nitro Monster Truck RTR.Features: Aluminum construction that’s blue anodized...
View full detailsAir filter body (high-volume)/ filter support/ cap/ foam filter, pre-filter/ Revo® air filter base (angled)/wire mount/hardware (1 each) (TRX® Eng...
View full detailsThis is the optional 36 tooth spur gear for the Traxxas Revo monster truck. This spur gear goes on the gear box to transfer power from the clutch b...
View full detailsThis is a 4x10mm button head screw set for the Traxxas Revo vehicle.Features: Steel construction that’s black in color Low-profile, button-head de...
View full detailsTurnbuckles, toe link, 59mm (78mm center to center) (2) (assembled with rod ends and hollow balls) 59 mm (78 mm center to center) adjustable toe l...
View full detailsBox, receiver (sealed)/ foam pad/2.5x8mm CS (4)/ 3x10mm CS (2) Sealed receiver box for Traxxas micro receivers. Includes foam pad, silicone seal...
View full detailsScrews, 3x14mm button-head machine (hex drive) (6) 3x14 mm button-head machine screws with hex drive heads. Set of six. Replacement part for thes...
View full detailsScrews, 3x30mm button-head machine (hex drive) (6) 3x30 mm button-head machine screws with hex drive heads. Set of six. Replacement part for thes...
View full detailsThis is a pair of Fully Assembled (without springs) Long Green-Anodized GTR Shocks from Traxxas. Features: Hard Anodized PTFE Aluminum Bodies T...
View full detailsThis is a replacement Traxxas 122.5mm Heavy Duty Steel Constant-Velocity Driveshaft; shaft only.
This is a replacement Traxxas X-Maxx Hardened Steel Shock Mount Suspension Pin Set, including two 4x25mm and two 4x38mm pins. For use in the front ...
View full detailsThis is the Traxxas Ring gear, differential/ pinion gear, differential (metal). This is Traxxas part number 7683Part Number: 7683 / TRA7683FitsLaTr...
View full detailsSpur gear, 55-tooth 55-tooth spur gear (48-pitch) with telemetry magnet holder. Traxxas spur gears let you fine-tune the performance of your Traxx...
View full detailsWheel hubs, splined, 17mm, short (blue-anodized) (4)/ wheel nuts, splined, 17mm (blue-anodized) (4)/ hub retainer M4 X 0.7 (4)/ axle pin (4) (Slas...
View full detailsTraxxas Aluminum Caster Blocks are CNC Machined from 6061 Aluminum, and will increase the durability of the front end of the Slash 4x4, Rustler 4x...
View full detailsThis is the Traxxas Front/Rear Body Mount for the Slash 4x4.Features: Black colored For the Traxxas Slash 4x4 Hardened plastic construction Inclu...
View full detailsThis is an optional Traxxas Center Driveshaft Set, and is intended for use with the Traxxas E-Revo and Summit trucks. Traxxas Steel Constant Veloci...
View full detailsThis is the steering arm mount for the Traxxas Revo.Features: Black plastic construction Standard and maximum throw steering stops Includes: Stee...
View full detailsSkid plate set, front (2 pieces, plastic)/ skid plate, rear (1 piece, plastic) Skid plate set includes front and rear skid plates. Replacement pa...
View full detailsThis is the motor and pinion gear for the Traxxas EZ Start 2 (R) System.Features: Pre-installed 10 tooth pinion gearIncludes: Motor and Pinion Gear...
View full detailsThis is the Replacement O-ring header gasket for the Traxxas 2.5 Engine.This is located on the header of the engine.FEATURES:Red silicone construct...
View full detailsThis is a package of replacement caster spacers for the Traxxas 2.5 T-Maxx. These spacers adjust caster of the wheels.Features: Black nylon constru...
View full detailsALUMINUM CASTER BLOCKS: Traxxas aluminum caster blocks improve the appearance, ruggedness, and control on the your Traxxas model. In addition to th...
View full detailsScrews, 3x10mm cap-head machine (6) (no washer)
Rod ends (16 long & 4 short)/ hollow ball connectors (18)/ ball screws (2) Set of replacement rod ends with 16 long ends and 4 short ends. Inc...
View full detailsDriveshafts, front, steel-spline constant-velocity (complete assembly) (2) Extreme heavy-duty front steel CV (constant velocity) driveshafts are e...
View full detailsDifferential kit, center (complete) (aluminum carrier) Replace your Traxxas vehicle’s stock slipper clutch with this Pro-Built high-performance ce...
View full detailsBall bearings, black rubber sealed (5x8x2.5mm) (2) Pair of 5x8x2.5 mm black rubber seal ball bearings. A step above blue-seal bearings, black-seal...
View full detailsO-ring and seal set, carburetor/ O-rings: 2x1mm (3), 10x1mm (4), 2.5x1.15mm (2), 6.2x1.2mm (1)/ 5x.9mm O-ring installation tool/ 5.3x7.8x.6mm crus...
View full detailsThis is a pair of gear covers for the Traxxas X-Maxx Monster Truck. Features: Molded composite plastic construction Fastens to upper rear bulkhead...
View full detailsThis is a pair of upper suspension arms for the Traxxas X-Maxx Monster Truck. Features: Molded composite plastic construction for reduced weight F...
View full detailsTraxxas 48 Pitch Spur Gears are available in 45, 50 or 55 tooth count options to fine tune the gear ratio of your model. Fits: Traxxas 1/16 E-Revo...
View full detailsHalf Shaft Set, Long (Plastic Parts Only) (Internal Splined Half Shaft/ External Splined Half Shaft/ Rubber Boot) (Assembled w/ Glued Boot) (2 Asse...
View full detailsBall bearings, blue rubber sealed (4x7x2.5mm) (2) Upgrade your standard plastic bellcrank bushings with these 4x7x2.5 mm blue-seal bearings for ...
View full detailsSpur gear, 58-tooth (0.8 metric pitch, compatible with 32-pitch) 58-tooth spur gear (32-pitch). Traxxas spur gears let you fine-tune the performan...
View full detailsThese are the 4x16mm Button Head Machine Screws from Traxxas.Features: For use in the Traxxas Revo and also anywhere a screw this size is required...
View full detailsScrews, 3x18 button-head machine (hex drive) (6) 3x18 mm button-head machine screws with hex drive heads. Set of six. Replacement part for these ...
View full detailsTurnbuckles, toe link, 55mm (75mm center to center) (2)
Rustler 4X4 LED Light Kit Built Traxxas Tough™The Traxxas Rustler® 4X4 takes stadium truck performance to new heights. The all-new High-Output Off...
View full detailsTraxxas Antenna Crimp Nut & Antenna Nut Tool Jato Features: Anodized Blue Aluminum crimp nut Includes: One crimping nut Nylon wrench Part...
View full detailsCarrier, differential/ x-ring gaskets (2)/ ring gear gasket/ 16X23.5X.5 TW Differential carrier includes X-ring gaskets (2), ring gear gasket, and...
View full detailsWe invite you to join our mailing list to receive specials and promotions.
EMAIL: sales@bigboyswithcooltoys.ca
MISSISSAUGA LOCATION: OR-
TEXT 647-321-1965
Need help ONLINE ?
text online support MESSAGES WILL BE ANSWERED
from 11am to 5pm - EST- 7 DAYS A WEEK
** Response times From senior staff 2 TO 3HRS