TRAXXAS CARS AND TRUCKS AND PARTS IN STOCK 2025

Traxxas Output Shaft, Transmission

Traxxas Body, GTM Shock, 6061-T6 Aluminum (Red-Anodized) (Includes Spring Pre-Load Spacers) (2)

Traxxas Body, GTM Shock, 6061-T6 Aluminum (Orange-Anodized) (Includes Spring Pre-Load Spacers) (2)

Traxxas Body, GTM Shock, 6061-T6 Aluminum (Green-Anodized) (Includes Spring Pre-Load Spacers) (2)

Traxxas Body, GTM Shock, 6061-T6 Aluminum (Dark Titanium-Anodized) (Includes Spring Pre-Load Spacers) (2)

Traxxas Body, GTM Shock, 6061-T6 Aluminum (Blue-Anodized) (Includes Spring Pre-Load Spacers) (2)

Traxxas Axle Shafts, Front, Outer

Traxxas Frame Mount, Flatbed (4)/ Stiffener (Fits TRX-6 Ultimate RC Hauler)

These are the Traxxas E-Revo 2.0 Red Front Left Upper & Lower Heavy Duty Suspension Arms

This is a replacement Traxxas Maxx Steel Constant-Velocity Driveshaft, intended for use with the Maxx 1/10 Brushless Monster Truck. Use only with T...

This is the Steel-Spline Constant Velocity Differential Output Shafts from Traxxas. Includes: (2) Differential Output Shafts   Requires: Ins...

This is Transmission Input and Output Shafts for the Traxxas TRX-4 and TRX-6. Features: Metal in Construction   Includes: (1) Input Shaft, (...

This is a pack of two replacement Traxxas 4-Tec 2.0 Stub Axles. Features:Factory Replacement Part Includes:(2) Stub Axles

This is the Traxxas silver-anodized aluminum GTS shock body.

High-speed needle valve & seat assembly (w/ securing nut) Replacement part for these models: TRX® Pro .15 TRX® Pro .15 Marine

Traxxas 3994X Shaft Low Idler Gear Shaft E-Maxx This is the Lightweight Output/Idler Gear Shaft for the Traxxas E-Maxx.This shaft is located in th...

This is a replacement Traxxas Temperature & Voltage Telemetry Sensor, and is intended for use with the Traxxas XO-1. Temperature data is critic...

This is an optional Traxxas "Short" Temperature & Voltage Sensor. Temperature data is critical to monitoring performance, gauging the effects o...

Traxxas Water Cooling Jacket Spartan Features: Rubber construction Includes: Water Motor Cooling Jacket Fits: Traxxas Spartan

This is the locking differential ouput gear for use on the Traxxas Summit Truck RTR.Features: Steel constructionIncludes: Locking Differential Out...

This is a Traxxas Differential Gear Set for the Jato. Includes:2x Output Gears2x Spider Gears1x Spider Gear Shaft

This is the optional differential spool for the Traxxas Revo.Features: Constructed of steel Installs in diff housing on either front or rear wheel...

TRA5215 Clutch bell (15-tooth)/5x8x0.5mm fiber washer (2)/ 5mm eclip(requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)

This is the optional differential spool for the Traxxas T-Maxx Truck. This is located in the bulkhead and eliminates the differential. This part is...

Traxxas optional stainless steel suspension pin set for the Traxxas T-Maxx or E-Maxx Monster Trucks. These suspension pins hold the upper and lower...

Traxxas aluminum engine mounting set is constructed of aluminum. Hex drives and Phillips drive. This set has all of hardware to assemble the engine...

Traxxas clutch bells are made from durable steel for long-lasting performance. Available in a variety of sizes to fine tune your truck's gear ratio...

Idler gear, machined-aluminum (not for use with steel top gear) (hard-anodized) (30-tooth)

This is a 2WD Gear Hub and Snap Ring for the Traxxas Nitro 4-Tec. COMMENTS: There are two spur gear pins molded into the gear hub. pjm 2/12/03 ir/jxs

Flywheel and pins (2)

This is the LED roof lightbar in chrome for the Traxxas 1/16 scale Summit.Features: Adds lights to the 1/16 scale Summit for added scale realismInc...

These are the decal sheets for the 1/10 scale 4x4 Traxxas Slash.Features: Full-color sponsor, body trim and Traxxas logos in various sizes Precut ...

This is a replacement Traxxas 77mm Aluminum Rear GTR Shock Body for the Unlimited Desert Racer. This shock body is 77mm long and features no thread...

Traxxas pair of SCT Split Spoke Wheels in Red. Fits front and rear of the Slash 4x4 and the rear of the 2 wheel drive Slash. Red colored wheel with...

This is a pair of SCT Wheels in Satin/Chrome/Black from Traxxas.FEATURES:Fits front and rear of the Slash 4x4 and the rear of the 2 wheel drive Sla...

This is the driveshaft assembly for the Traxxas Jato. These Driveshafts transfer power from the gearbox to the rear wheels.Features: Fully assemble...

The 12-Volt adapter provide a 12-Volt accessory-style output with bullet connectors.

Speed bit handle, premium (rubber overmold) The premium speed bit handle holds bits securely with an overmolded rubber grip to provide excellent...

Traxxas Skid plate (roof)/ tailgate protector (green)/ mounts (2)/ 3x8mm BCS (7) (fits #10711 body)

This is the Traxxas Rear Chassis Brace for the E-Revo and Summit.Features: Blue colored Made of durable aluminum For the Traxxas E-Revo and Traxxa...

This is a set of Traxxas Maxx’s extreme-duty cold-weather suspension arms, available in 6 colors to allow you to customize your truck to your style...

This is the Traxxas Clockwise Motor with a High Output Red Connector for the Latrax Alias Quadcopter.Features: Color of connector indicates rotati...

Spool/ differential housing plug/ e-clip/ 2.5x8mm BCS (with threadlock) (4) The differential spool replaces the remote-locking differential in TRX...

Traxxas Gear, 13-T pinion (1.0 metric pitch) (fits 5mm shaft)/ set screw Machined, Hardened Stee

Servo horn (with built-in spring and hardware) (for Summit locking differential) Shift servo horn with built-in spring tensioner Replacement part...

Traxxas Suspension Pin Retainer 6061-T6 Aluminum (Gray-Anodized) (4)