FEATURES: Plastic construction Black in color INCLUDES: One Air Filter Housing One Foam Insert Element One Rubber Filter Base One Cable Tie SPECS: ...
View full details
This is a replacement flywheel nut from Traxxas.Features: Metal construction Used on the Traxxas TRX 2.5. engine Includes: Flywheel Nut
These are replacement cooling head protectors for the Traxxas 2.5 Engine. These attach to the top of the cooling head.Features: Black nylon constru...
View full details
TRA5215 Clutch bell (15-tooth)/5x8x0.5mm fiber washer (2)/ 5mm eclip(requires 5x11x4mm ball bearings part #4611) (1.0 metric pitch)
These are the wheelie bar wheels for the Traxxas 3.3 T-Maxx.Features: Constructed of hard plastic Axles constructed of steel Includes: Four wheel...
View full details
Traxxas battery box replaces damaged battery boxes. Constructed of gray plastic. This battery box mounts to the chassis and protects the battery pa...
View full details
This is a package of 3X20mm Flat Head Countersunk Hex Screws by Traxxas.FEATURES:Flat head countersunk screw with a hexagon drive insertINCLUDES:Si...
View full details
This is a replacement slipper press plate for the Traxxas Rad2, Hawk2, Nitro Hawk, Nitro Street, TRX-T Eagle, Blue Eagle, and Blue Eagle LSII.Inclu...
View full details
This is a replacement fuel tank for the Traxxas Nitro Rustler Stadium truck kitFeatures:Clear plastic, flip-top style tank for glow fuel only.Nippl...
View full details
Traxxas Shoulder screws, 3x10mm (6) (with threadlock)
The extended quick release battery hold downs for E-Maxx® make it easy to install small or large format, multi-cell battery packs. Stock E-Maxx hol...
View full details
This is the replacement battery hold down set for the Traxxas E-Maxx.Features: Black nylon construction Adhesive backed foam strips Fits standard ...
View full details
Turnbuckles, aluminum (red-anodized), camber links, front, 39mm (2), rear, 49mm (2) (assembled w/ rod ends & hollow balls)/wrench Traxxas’ alu...
View full details
Traxxas Seal Kit Rx Box Features: Properly seals receiver box to minimize dirt and moisture exposure Includes: Silicone grease One Gasket Two Fo...
View full details
Screws, 2.5x6mm cap-head machine (hex drive) (6) Set of six 2.5x6 mm cap-head machine screws with hex-drive heads Replacement part for these mode...
View full details
Spur gear (66-Tooth) (32-Pitch) w/bushing
Turnbuckles, aluminum (red-anodized), toe links, 59mm (2) (assembled with rod ends & hollow balls) (requires 5mm aluminum wrench #5477)
Wiring harness, on-board radio system (includes on/off switch and charge jack) (Jato)
Plug Adapter (For TRX Power Charger to charge 7.2V Packs)
Shock caps, aluminum (2) (Big Bore Shocks) Replacement aluminum shock caps for Traxxas Big Bore shocks. (2) Caps do not fit Ultra Shocks. Access...
View full details
Screws, 3x6mm countersunk machine (6) (hex drive)
Turnbuckles, aluminum (blue-anodized), toe links, 61mm (2) (assembled with rod ends & hollow balls) (fits Stampede) (requires 5mm aluminum wren...
View full details
Gear, 18-T pinion (48-pitch) / set screw 18-Tooth Pinion Gear (48-Pitch) fits 3 mm motor shafts and includes set screw. Traxxas pinion gears let y...
View full details
Traxxas Front & Rear Skid Plate Set (Green) (Grave Digger)
TRA9517G Traxxas Wing/ wing washer (green)
TRA9542 Traxxas Suspension pins, outer, front, 3.5x48.2mm (hardened steel) (2)/ M3x0.5mm NL, flanged (2)
TRA9548 Traxxas Camber links, rear (2) (assembled with hollow balls)
Traxxas Body, Maxx V2, blue (painted, decals applied) (fits Maxx V2 with extended chassis (352mm wheelbase))
This is a replacement Traxxas Rear Ring Gear and Pinion Gear Set for the Unlimited Desert Racer. This set is for use in the rear axle only.
Driveshaft assembly (1), left or right (fully assembled, ready to install)/ screw pin (1) Fortified for hard launches and superior durability, Ex...
View full details
This is a wheelie bar with Mount for the Traxxas Drag Slash Features: Plastic Included: (1) Wheelie Bar with Mount
Ball bearings, blue rubber sealed (4x8x3mm) (8) Set of eight 4x8x3 mm blue rubber seal ball bearings. Blue-seal ball bearings keep dust and grime ...
View full details
Customize your Drag Slash Chevrolet C10 body with this grille and bumper set. The bright chrome finish gives your truck an extra dose of style. Inc...
View full details
Stub axle, aluminum (black-anodized) (1) (for use only with #7750X or 7896 driveshaft) Add a touch of style to your X-Maxx® or XRT® with this br...
View full details
This is a replacement Traxxas X-Maxx Aluminum Stub Axle. This anodized aluminum stub axle is for use with 8s-spec heavy duty driveshaft (TRA7750X) ...
View full details
This is a Traxxas Stampede Long Comp Black Chassis, intended for use as a replacement for the Bigfoot kits and as an optional part for the Stampede...
View full details
Traxxas Unlimited Desert Racer GTR Double Shock Seal Kit. This optional shock seal kit is intended for the Traxxas Unlimited Desert Racer. Using x-...
View full details
This is a Traxxas TRX-4 Rear Bumper, intended for use as an optional accessory part for Traxxas TRX-4 1979 Chevrolet Blazer and a replacement for t...
View full details
This is the Heavy Duty Rear Left Suspension arms for the E-Revo VXL Brushless by Traxxas. Part # 8934X Features: Heavy Duty Blue in color ...
View full detailsWe invite you to join our mailing list to receive specials and promotions.
EMAIL: sales@bigboyswithcooltoys.ca
STORE LOCATION: OR-
TEXT 647-321-1965
Need help ONLINE ?
text online support MESSAGES WILL BE ANSWERED
from 10am to 3pm - EST- 7 DAYS A WEEK
** Response times From senior staff 2 TO 3HRS
