Traxxas assembled tuned pipe is made of molded composite construction with rubber header gasket. Black in color Includes: One Molded Composite Tune...
View full details
Traxxas 7668X Wheel Nut Washer Aluminum Orange 3x12mm CS (4) LaTrax Teton / SST These are the Wheel Nut Washers for the LaTrax Teton Monster Truck ...
View full details
This is a set of four Traxxas Machined Aluminum Wheel Nut Washers in Red with four 3x12mm Cap Screws for the 1/18 scale LaTrax Desert PreRunner. Fe...
View full details
These are the optional wheel nut washers for the LaTrax Teton Monster Truck from Traxxas.Features: Green colored Made of aluminum For the LaTrax T...
View full details
This is the Traxxas ExoCage, 1/16th Summit (includes mounting hardware). This is Traxxas part number 7220Part Number: 7220 / TRA7220Fits1/16 Summit...
View full details
This is a replacement Traxxas Steel Driveshaft Rebuild Kit, and is intended for use with the Traxxas 1/16 E-Revo and Slash trucks, as well as the 1...
View full details
This is a replacement Traxxas Center Differential Gear Set, and is intended for use with the Traxxas Slash 4x4.
This is the Traxxas Complete High Stall Clutch Gear for the Telluride 4x4.Features: Black and silver/grey colored Made of tough plastic and steel ...
View full details
Bulkhead, Rear (Left & Right Halves) for Summit Replacement Part For: Summit (Model# 56076-4)
This is the front bulkhead for use on the Traxxas Summit Truck RTR.Features: Nylon construction that is black in colorIncludes: One Front Bulkhead ...
View full details
This is the Plastic Tuned Pipe for use with the Traxxas 2.5 and 2.5R engine equipped vehicles.FEATURES:Black plastic constructionDirect replacem...
View full details
Exhaust header Replacement part for these models: TRX® Pro .15
This is a replacement Traxxas Unlimited Desert Racer Motor Mount, with two included pins. Features:Factory Replacement Mount Includes: (1) Motor M...
View full details
TRA9545 Traxxas Servo saver/ servo saver spring/ servo horn, steering (assembled)
This is an optional pack of four Traxxas Fender Extensions, intended for use with TRX-4 and TRX-6 Kits. Includes: (4) Fender extensions (24) 3x8...
View full details
The Traxxas TRX-4 1972 Chevrolet Blazer Grille is a great way to add the classic 1972 grille to your Traxxas TRX4 equipped with the optional 1972 B...
View full details
TRA8870X Traxxas Fairlead, winch, aluminum (blue-anodized)
TRA8870R Traxxas Fairlead, winch, aluminum (red-anodized)
Spur gear, steel, 54-tooth (0.8 metric pitch, compatible with 32-pitch) (for center differential) The 54-tooth steel spur gear (32-pitch) fits the...
View full details
Rod end set, complete (standard (10), angled 10-degrees (8), offset (4)) Rod end set features standard rod ends (10), 10-degree angled rod ends ...
View full details
Traxxas 7541 LaTrax Rally Bushings 4x8x3mm (2) 6x10x3mm (8) 8x12x3.5mm (5)This is the Bushing Set for the Latrax Rally Car from Traxxas.FEATURESNyl...
View full details
Input shaft/ drive gear assembly, lightweight (18/ 13-tooth top gear) (hard-anodized/PTFE-coated 7075 T6 aluminum gears)
This is the black wing for the Traxxas Revo 3.3. This part attaches to the rear of the body.Features: Plastic construction that’s black in colorInc...
View full details
This is a replacement Traxxas Maxx Driveshaft Assembly, intended for use with the Maxx 1/10 Brushless 4WD Monster Truck. Features: Factory Replac...
View full details