TRA4940 Exhaust Header, Blue: TMX
TRAXXAS
This is the Exhaust Header for the Traxxas T-Maxx Kit with the .15 engine.This part is attached to the engine.FEATURES:Blue anodized aluminum heade...
View full details
This is the Exhaust Header for the Traxxas T-Maxx Kit with the .15 engine.This part is attached to the engine.FEATURES:Blue anodized aluminum heade...
View full details
Traxxas assembled tuned pipe is made of molded composite construction with rubber header gasket. Black in color Includes: One Molded Composite Tune...
View full details
Traxxas 5194X Reverse Upgrade Kit SportMaxx This is the optional Sportmaxx Reverse Upgrade Kit from Traxxas.This will mount into the transmission a...
View full details
TRA5192X 2-SPD UPGRADE SPORTMAXX (right side of C)
Traxxas Drive Cup/Screw Pin M4/15 Features: Metal construction, red and silver in color Steel CV center driveshaft Includes: One sleeve One M4/1...
View full details
This is a 2WD Gear Hub and Snap Ring for the Traxxas Nitro 4-Tec. COMMENTS: There are two spur gear pins molded into the gear hub. pjm 2/12/03 ir/jxs
Traxxas Pro .15 to TRX 2.5 engine conversion has a tune Pipe, bellcrank, & Throttle Servo Horn made of plastic. Linkage wire made of steel. Spe...
View full details
Backplate (for recoil start engines) Replacement part for these models: TRX® Pro .15 TRX® Pro .15 Marine
High-speed needle valve & seat assembly (w/ securing nut) Replacement part for these models: TRX® Pro .15 TRX® Pro .15 Marine
Clutch bell, hardened steel (20-tooth) (32-pitch) (N. Hawk/Buggy/Street) ¶ÿ Accessory part for these models: TRX Pro .15
Traxxas Toe Links Slayer Features: 7075-T6 aluminum construction Fits front or rear Anodized Red Includes: Two Toe Links Eight Ball Ends One 7mm...
View full details
Traxxas 3994X Shaft Low Idler Gear Shaft E-Maxx This is the Lightweight Output/Idler Gear Shaft for the Traxxas E-Maxx.This shaft is located in th...
View full details
This is a pair of Traxxas Pre-Assembled SCT Beadlock Style Dual-Profile Wheels in Red and SCT Off-Road Racing Tires for the 1/18 scale LaTrax Deser...
View full details
This is a set of four Traxxas Machined Aluminum Wheel Nut Washers in Red with four 3x12mm Cap Screws for the 1/18 scale LaTrax Desert PreRunner. Fe...
View full details
This is the rear LED light harness for the Traxxas 1/16 scale Summit.Features: Adds lights to the 1/16 scale Summit for added scale realism and it ...
View full details
This is the LED roof lightbar in chrome for the Traxxas 1/16 scale Summit.Features: Adds lights to the 1/16 scale Summit for added scale realismInc...
View full details
This is a set of Dual Profile Tires for the Traxxas Monster Jam series.FEATURES:Rubber construction, split vee designINCLUDES:Two Dual Profile Tire...
View full details
FEATURES: Aluminum construction, gun metal gray in color INCLUDES: Chassis Brace
This is the Front Bumper and Mount for the Traxxas Slayer Pro 4WD Short Course Nitro RTRFEATURES:Nylon constructionBlack in colorINCLUDES:One Front...
View full details
This is a pair of SCT Wheels in Satin/Chrome/Black from Traxxas.FEATURES:Fits front and rear of the Slash 4x4 and the rear of the 2 wheel drive Sla...
View full details
This is the Traxxas Blue Aluminum Drive Strut for the DCB M41 boat.FitsDCB M41 boats
Traxxas motor plate is constructed of blue anodized aluminum. This part holds the motors onto the truck. Requires: Installation on the E-Revo truc...
View full details
This is a Traxxas Differential Gear Set for the Jato. Includes:2x Output Gears2x Spider Gears1x Spider Gear Shaft
This is a package of Threaded Ball Studs fromTraxxas for use on the Jato 2.5.These are used for the inner camber link mounting.FEATURES:Hard anodiz...
View full details
Features: Anodized Blue in Color 6061 T6 Aluminum Construction Countersunk Screw Holes Includes: One Blue Aluminum Chassis
Traxxas set of the Hurricane Chrome Wheels used on the Traxxas Revo. Five spoke chrome plated construction. Also fits Traxxas T-and E-Maxx vehicles...
View full details
Traxxas package of thirty aluminum hollow balls for the Revo.Constructed of gun metal gray colored aluminum.Two tall offset aluminum hollow balls a...
View full details
This is the Replacement Drive Hub Assembly for the Traxxas T-Maxx 4WD Radio Control Monster Truck.This drive hub assembly fits into the spur gear a...
View full details
Exhaust header Replacement part for these models: TRX® Pro .15
TRA9597 Traxxas Mounts, sway bar/ collars (front and rear)
TRA9584 Traxxas Mount, center differential
TRA9598 Traxxas Linkage, sway bar (front or rear)
TRA9590 Traxxas Gear adapter, fixed (A)/ motor mount spacer
TRA9546 Traxxas Draglink, steering/ 3x14mm SS (2)
Half shafts, outer (extended, front or rear) (4)/ e-clips (8) (for use with #8995 WideMaxx™ suspension kit)Accessory part for these models:Maxx®
This is the Traxxas 1/10 Maxx Waterproof Receiver Box Seal Kit with O-ring, Seals, and Silicone Grease Stock Replacement OnMaxx 4S
This is a replacement Traxxas Drive Wheel. This is for use with the Traxxas TRX-4 All Terrain "Traxx" TRA8880. Features: Factory Replacement Drive...
View full details
This is a Traxxas Inner and Outer Bearing Retainer Set. Includes:2x Inner Bearing Retainers2x Outer Bearing Retainers
We invite you to join our mailing list to receive specials and promotions.
EMAIL: sales@bigboyswithcooltoys.ca
STORE LOCATION: OR-
TEXT 647-321-1965
Need help ONLINE ?
text online support MESSAGES WILL BE ANSWERED
from 11am to 4pm - EST- 7 DAYS A WEEK
** Response times From senior staff 2 TO 3HRS