This is a 26 Tooth Gear for the Traxxas T-Maxx Forward Only Shaft.FEATURES:This is the gear for the shaft that converts the T-Maxx to forward only ...
View full details
Traxxas Gear Shaft Primary Features: Replaces stock gear shaft. Constructed of steel. Includes: One gear shaft Part Compatibility: Traxxas S-...
View full details
FEATURES: Fits first generation T-Maxx transmission without OptidriveSteel shaft with plastic gear22T and 17T gearsPre-assembled on shaft INCLUDES:...
View full details
Traxxas replacement gear hub assembly for the T-Maxx 4WD Radion Control Monster Truck. This is the replacement gear hub assembly. This gear hub ass...
View full details
This is the optional differential spool for the Traxxas T-Maxx Truck. This is located in the bulkhead and eliminates the differential. This part is...
View full details
Replaces stock silver pivot ball aluminum caps. Constructed of blue aluminum.
TRA4919 Servo mounts, throttle/ brake (1) (black)
Traxxas servo steering/shift mounts for the T-Maxx 3.3 are made of gray plastic construction. Includes: Two mounts Specs:Length: 1-1/2" (38mm)Widt...
View full details
These are 20 Groove Middle Pulleys by Traxxas.FEATURES:Black in colorHard Plastic Construction for the Pulleys and Flanges.Metal Construction for t...
View full details
Traxxas optional 45T spur gear is constructed of black nylon. INCLUDES: One 45T spur gear. This is listed in the manual as the 1st gear.
Traxxas Clutch Gear 2nd Speed 19T Features: Steel Construction Includes: One 19 Tooth Gear Specs: # Teeth: 19T Part Compatibility: Traxxas ...
View full details
FEATURES: Steel Construction INCLUDES: One Gear REQUIRES: Traxxas Clutch Bell SPECS: Length: 6 mm (0.243") Diameter: 17 mm (0.675") Teeth: 15
FEATURES: Constructed of aluminum. INCLUDES: One Traxxas Exhaust Header Set for the Nitro 4-Tec and the Nitro Sport with: One Pipe Two 3mm x 25mm S...
View full details
This is the fuel tank rebuild kit for the Traxxas Rustler.Features: Direct fit replacement partsIncludes: Tank cap Tank seal Tank cap spring Small...
View full details
This is the Receiver Cover for theTraxxas Nitro Slash Short Course Racing Truck,FEATURES:Plastic constructionFastens to chassis and fits over recei...
View full details
TRA4428 EZ-Start mount/ clamp/ 2.6x10mm RST (4)
VEN4036R ATOMIK ALLOY REAR SKID PATE 1:10 TRAXXAS E-REVO - RED
This is the Rear Grey Bulkhead for the Traxxas Nitro Stampede. Features Sturdy grey nylon construction Includes One rear bulkhead for the Traxxas N...
View full details
These cool, 5-spoke chrome wheels can be used to replace the dished wheels on older models. The TRX Pro-Star wheels feature a chrome-less gluing su...
View full details
Traxxas clutch bells are made from durable steel for long-lasting performance. Available in a variety of sizes to fine tune your truck's gear ratio...
View full details
Traxxas 3994X Shaft Low Idler Gear Shaft E-Maxx This is the Lightweight Output/Idler Gear Shaft for the Traxxas E-Maxx.This shaft is located in th...
View full details
This is the optional Single Motor Gear Cover for theTraxxas E-Maxx 16.8V RTR, TRAD22**.FEATURES:Constructed of plasticAllows installation of a sing...
View full details
This is the Replacement Battery Hold Down Set for the Traxxas E-Maxx Truck. These hold downs screw directly into the chassis.Features: Black nylon...
View full details
Tray, radio/ drive shaft mount w/ pressure fitting
¶ÿRebuild kit, Velineon 380 (4x9x4mm ball bearings (2), 2x6mm CCS (with threadlock) (2), front shims (2))
Power adapter, DC (12V car adapter for TRX Power Charger)
Suspension pin set, stainless steel (w/ E-clips)
Save 50%
Screws, 2.6x10mm roundhead self-tapping (6)
This is a pack of two Team Losi Racing Lexan Body Washers, and are intended for use with the Team Losi 8IGHT 2.0 1/8 scale buggies.¶ôǨ
