TRA6642 LaTrax Alias Bearing 3x6x2mm (8) Replacement pack of LaTrax Alias 3x6x2mm bearings parts for these models: LaTrax Alias Quad Rotor Helic...
View full details
This is the Battery Charger for the optional NiMH Batteryused in the Traxxas TQi Docking Base.FEATURES:Charges the optional Traxxas #3037 NiMH batt...
View full details
Spring, header (for Revo big block header)/o-ring (1) & gasket (1) (for exhaust header flange)
Traxxas Needle Assembly High-Speed TRX 2.5 Features: Brass construction. Includes: One needle One fuel fitting Two 5.3x7.8x0.6mm washers Specs:...
View full details
This is the replacement cylinder head for theTraxxas 2.5 Truck/Buggy engine.FEATURES:Aluminum construction.INCLUDES:One aluminum cooling head (cyli...
View full details
Traxxas brake disc set for the 3.3 T-Maxx RTR is constructed of steel Includes: Brake Disc for the 3.3 Traxxas T-Maxx RTR COMMENTS: Fits the 3.3 ve...
View full details
Sold out
Pulley shaft, front (blue-anodized, light-weight aluminum) Lighter than the stock steel pulley shaft, the attractive, blue-anodized 6061-T6 aluminu...
View full details
This is a 48-pitch 84-tooth spur gear from Traxxas. The gear is molded from black plastic. This spur gear is for use with Traxxas' slipper clutch.I...
View full details
O-ring set: for carb base/ air filter adapter/high-speed needle (2)/ low-speed spray bar (2) Replacement part for these models: TRX® Pro .15 TRX®...
View full details
Dust boot, throttle Replacement part for these models: TRX® Pro .15 TRX® Pro .15 Marine
Wrist pin/ G-spring retainer (wrist pin keeper) (1) Replacement part for these models: TRX® Pro .15
Manufacturer Description This is the Replacement Carrier Drive Dog for Traxxas E-Maxx Truck.This part is located in the gearbox in between the two ...
View full details
Big Bore shocks (x-long) (hard-anodized and PTFE-coated T6 aluminum) (assembled with TiN shafts) w/o springs (2)
Big Bore shocks (short) (hard-anodized & PTFE-coated T6 aluminum) (assembled with TiN shafts w/ springs)(f/r)(2) (Note: Assembled with 32mm sha...
View full details
Save 25%
Sold out
Titan marine 550 motor, fan-cooled, 14 volts, 24-turns. Includes motor capacitors. Does not include wires or connectors (requires soldering)
Pushrod Boots for the Traxxas Villain EX boat FEATURES: Constructed of rubber, these boots protect and seal the steering rods INCLUDES: Two Steeri...
View full details
This is a pack of four green LaTrax Alias LED Lenses.
These are the Traxxas Orange LED Lenses for the LaTrax Alias Quadcopter.Features: Orange colored Made of durable plastic For the LaTrax Alias Quad...
View full details
These are the Traxxas Clear LED Lenses for the LaTrax Alias Quadcopter.Features: Clear colored Made of durable plastic For the LaTrax Alias Quadco...
View full details
This is a replacement LaTrax Alias Rotor Blade Set. Package includes one clockwise "A" blade, one counter clockwise "B" blade and replacement mount...
View full details
These are the Left and Right Steering Blocksused on the NHRA Funny Car Race Replica from Traxxas, TRAD69**.FEATURES:Plastic construction, black in ...
View full details
Rubber seals that install in the radio box lid for the antenna tube and the on-off switch.
This is a replacement Idle Mixture Screw for theTraxxas TRX 2.5 Carb (TRAG5252).FEATURES:Pre-installed gasketINCLUDES:One NeedleSPECS:Length: 13.8 ...
View full details
This is the replacement tie-rod set for the Traxxas 4-Tec. This set includes steering and camber links.Features: Black nylon rod ends and Steel stu...
View full details
This is the Shift Linkage Set for the Traxxas 3.3 T-Maxx.FEATURES:Installs on shift servo and controls shifting of the transmissionINCLUDES:Servo h...
View full details
Input shaft/ drive gear assembly, lightweight (18/ 13-tooth top gear) (hard-anodized/PTFE-coated 7075 T6 aluminum gears)
Traxxas left and right rear suspension arms are constructed of black plastic. Includes: Two suspension arms. Specs: Length:Â 62.0mm (2.443")Width:Â 3...
View full details
Traxxas Wheel Adapter Features: Allow the use of Aftermarket Wheels to be Used. Includes: Four Wheel Adapters Part Compatibility: Traxxas Nit...
View full details
This is a slipper pressure plate and hub for the Traxxas X-Maxx Monster Truck. Features: Cast metal construction Installs on transmission input sh...
View full details
FEATURESHardened steel constructionSplined to hold the pressure plate, slipper clutch and spur gearassemblies in place INCLUDESTransmission Input S...
View full details
These are the optional wheel nut washers for the LaTrax Teton Monster Truck from Traxxas.Features: Green colored Made of aluminum For the LaTrax T...
View full details
These are the optional wheel nut washers for the LaTrax Teton Monster Truck from Traxxas.Features: Blue colored Made of aluminum For the LaTrax Te...
View full detailsWe invite you to join our mailing list to receive specials and promotions.
EMAIL:Â sales@bigboyswithcooltoys.ca
STORE LOCATION: OR-
TEXT 647-321-1965
Need help ONLINE ?
text online support MESSAGES WILL BE ANSWERED
from 10am to 3pm - EST- 7 DAYS A WEEK
** Response times From senior staff 2 TO 3HRS
