Front Springs for Bandit (2); Pink

Traxxas Differential Cover, Front Or Rear (Black) (2)

Traxxas Wire Harness (For Use With #3475 Cooling Fan)

TRA4980X Housings, diff (ring side/ non-ring side) (1 each)/ pinion collar (1)

This is the fuel tank rebuild kit for the Traxxas Rustler.Features: Direct fit replacement partsIncludes: Tank cap Tank seal Tank cap spring Small...

Ball bearings, black rubber sealed (4x10x4mm) (2) Pair of 4x10x4 mm black rubber seal ball bearings. A step above blue-seal bearings, black-seal b...

This is a replacement Traxxas 4-Tec 2.0 Front and Rear Body Mount Set. Features:Factory Replacement Body Mount Set Includes:(1) Body Mount Set

These are the GTR shock shafts for use on the Traxxas 1/16 E-Revo and Slash VXL vehicles.Features: Aluminum construction that is silver in colorInc...

These are the rod ends for the 1/16 scale Traxxas Revo and Slash series.Features: Black nylon constructionIncludes: Eight Nylon Rod Ends Eight Nyl...

Traxxas 5677A Cover Gear 3x8mm CS Revo (1)This is the Gear Cover for the Traxxas Revo.FEATURESPlastic construction, black in colorFor the single mo...

TRA9542 Traxxas Suspension pins, outer, front, 3.5x48.2mm (hardened steel) (2)/ M3x0.5mm NL, flanged (2)

Ball bearings, black rubber sealed (5x10x4mm) (2) Pair of 5x10x4 mm black rubber seal ball bearings. A step above blue-seal bearings, black-seal b...

This is the Rear Differential Housing for the Traxxas 4-Tec 2.0 chassis and Ford GT. Includes: (1) Rear Differential Housing  

Traxxas Screw pins, 3x16mm, extreme heavy duty (6) (for use with #9080 upgrade kit)

This is an optional Traxxas Rear Suspension Hinge Pin Mount Set. These blocks feature different anti-squat angles which will alter the suspension c...

This is optional Heavy Duty Rod Ends from Traxxas. Features: Heavy duty plastic construction Black in color   Includes: (8) Rod Ends   Spec...

This is a pair of replacement drive yokes for the Traxxas Revo. These yokes attach to the half shaft assemblies.Features: Black plastic constructio...

Traxxas Differential Cover, Front Or Rear (Grey) (2)

This is a set of inner drive cups and screw pins for the Traxxas Ford GT 4Tec.

This is a replacement Traxxas 4-Tec 2.0 Camber and Toe Link Set.  Features:Factory Replacement Part Includes:(6) Camber and Toe Links

This is a replacement Idle Mixture Screw for theTraxxas TRX 2.5 Carb (TRAG5252).FEATURES:Pre-installed gasketINCLUDES:One NeedleSPECS:Length: 13.8 ...

TRA5251 NEEDLE, LOW SPEED, TRX 2.5

This is a set of replacement Traxxas GTR shock caps with spring retainers, and are intended for use with the Traxxas 1/16 Slash, and 1/16 E-Revo ve...

This is the Center Driveshaft for the Traxxas 1/10 scale Telluride 4x4.FEATURES:Plastic construction, blue in colorINCLUDES:Center Driveshaft with ...

This is the housing for the front and rear differential on the Traxxas Summit Truck RTR.Features: Nylon construction that is black in colorIncludes...

This is the Brake Yoke w/Pins for the Traxxas Revo.It is use on the Center/Front Driveshaft Assembly.FEATURES:Plastic Brake YokeSteel Brake Pins(ea...

Traxxas Carrier, differential (planetary gears)/ differential spacer/ o-rings (2)/ ring gear gasket

This is the Offset Rod Ends for the Traxxas TRX-4 and TRX-6. Features: Plastic in Construction   Includes: (4) Offset Rod Ends

This is the Traxxas left and right tail light housing, lens and decals set.Includes: Two tail light housing Two lens Left and right decals

Ball bearings, black rubber sealed (7x14x5mm) (2) Pair of 7x14x5 mm black rubber seal ball bearings. A step above blue-seal bearings, black-seal b...

This is the Traxxas Nerf bars, chassis (black). This is Traxxas part number 5923Part Number: 5923 / TRA5923FitsSlayerSlayer Pro

These are the diff and trans drive yokes for the Traxxas T-Maxx 3.3.Features: Black plastic constructionIncludes: Two drive yokes Two 4x15mm Yoke ...

Traxxas Ball bearings, black rubber sealed (7x14x3.5mm) (2)

This is the Traxxas pair of Nerf Bars for the 1/10 scale Rally VXL, (2).Features: Black colored Made of plastic For the Traxxas Rally VXL Include...

Traxxas throttle and brake servo mounts for the T-Maxx 3.3 is constructed of gray plastic. Includes: Two servo mounts Specs:Length: 1-3/8" (36mm)Wi...

These are the 3mm x 10mm shoulder screws for the Traxxas Nitro Jato Stadium Truck.Features: Metal construction that’s black in colorIncludes: Six 3...

This is the Replacement Differential Output Yokes for the Jato by Traxxas. Features: Nylon construction Black in color   Includes: (2) Diffe...

FEATURES: Black plastic and steel wire construction INCLUDES: One ball link One straight linkage rod One coiled linkage rod One servo horn

Ball bearings, blue rubber shield (5x10x4mm) (2) Pair of 5x10x4 mm blue rubber seal ball bearings. Blue-seal ball bearings keep dust and grime out...

This is a set of two optional aluminum idler gear shafts from Traxxas. These idler shafts support the idler gears inside the transmission.

TRA3940 Screws, 4x4mm button-head machine, aluminum (blue) (hex drive) (6)

This is a replacement Traxxas Front & Rear Steel Bulkhead Tie Bar Set, and is intended for use with the Traxxas 1/16 Grave Digger Monster Jam R...

This is the 2nd Gear for the 2-speed for the Nitro 4-Tec.FEATURES:Black nylon colorINCLUDES:One gear 37 Teeth

Anchoring pins with locknuts (4)/ plastic thumbscrews for upper deck (4)

Traxxas tie-rods and upper camber rods are constructed of steel. Includes: Four Turnbuckles Two Draglinks. These turnbuckles are used on the steeri...

TRA4919 Servo mounts, throttle/ brake (1) (black)

TRA3959 Spur gear, 62-tooth (0.8 metric pitch, compatible with 32-pitch)