This is the Traxxas Upper Chassis/Battery Hold Down for the LaTrax Rally Car.Features: Blue colored Made of durable plastic For the LaTrax Rally C...
View full details
These are the Front and Rear Body Mounts for theTraxxas Telluride 4x4 from Traxxas, TRAD91**.FEATURES:Constructed of plastic, black in colorINCLUDE...
View full details
This is the outer driveshaft assembly for the VXL Summit from Traxxas.Features: Metal constructionIncludes: Driveshaft assemblyRequires: Installati...
View full details
These are the optional pivot ball caps for use on the Traxxas 1/16 E-Revo and Slash VXL vehicles.Features: Hard anodized aluminum Replaces stock p...
View full details
Stub axle, front, steel-splined constant velocity (1) Replacement steel front stub axle for Traxxas steel CV driveshafts (6851R). Accessory part ...
View full details
CHASSIS, LOW CG (BLACK) Change up the color on your low-CG-equipped 2WD Slash with this black chassis. Low-CG chassis do not fit standard 2WD Slas...
View full details
Gear, 18-T pinion (0.8 metric pitch, compatible with 32-pitch) (hardened steel) (fits 5mm shaft)/ set screw 18-tooth pinion gear (32-pitch) fits 5...
View full details
This is the battery compartment door for the Traxxas E-Revo.Features: Nylon construction that is black in colorIncludes: One Battery Compartment Door
This is the shim set for the Traxxas Nitro Jato Stadium Truck.Features: Metal construction that’s silver in color adjusting roll centerIncludes: Fo...
View full details
This is the chassis top plate for the Traxxas Nitro Jato Stadium Truck.Features: Nylon construction that’s black in color and holds receiver and th...
View full details
This is a pair of 5.9 rate (blue) shock springs for the Traxxas Revo.Features: Metal construction that’s red in color (small blue square indicates ...
View full details
Traxxas optional red aluminum pushrods for the rocker arms for the REVO. These go between the Rocker Arms and the Lower Suspension Arms. **Must be ...
View full details
Traxxas pair of driveshafts, outside U-joint is lubricated and sealed by a rubber boot to protect it from dirt and grime U-joint pins are held capt...
View full details
Traxxas rear plastic skidplate for the T-Maxx attaches to and protects chassis and supports the rear bulkhead. Skidplate is gray in color INCLUDES:...
View full details
TRA4914R Body mount posts, front (2)/ body mount, rear/ body mount screw pins (4)
Connector, wiring harness (EZ-Start® and EZ-Start® 2) Replacement wiring harness for the 4570 EZ-Start® and 5270R EZ-Start® 2 system. Replacement...
View full details
Flywheel (N. Rustler/Sport/Stampede/T-Maxx/Revo/Jato/Slayer) Replacement part for these models: Nitro Rustler® Revo® T-Maxx® TRX® 2.5R TRX® 3.3 T...
View full details
Air filter (complete with rubber base & foam insert) Replacement part for these models: TRX® Pro .15 Accessory part for these models: TRX® ...
View full details
Traxxas Cap Head Machine Screw 3x32mm (6) Features: Black finish Steel construction Cap head design Includes: (6) 3X32mm cap head machine screws...
View full details
These are the replacement bulkhead cross braces for the Traxxas E-Maxx. These Braces are located in between the bumper mounts.Features: Black nylon...
View full details
VXL-3m Electronic Speed Control, waterproof (brushless)
Wiring harness for RX Power Pack, Revo® (includes on/off switch and charge jack) Wiring harness for Revo and Slayer rechargeable receiver power pa...
View full details
Gear, 21-T pinion (48-pitch) / set screw 21-tooth pinion gear (48-pitch) fits 3 mm motor shafts and includes set screw. Traxxas pinion gears let y...
View full details
This is an optional Traxxas Aluminum Drag Link, intended for use with Traxxas Slash 4x4, Rustler 4x4 and Stampede 4x4 models. This machined alumin...
View full details
Suspension pins, inner, front or rear, 4x67mm (hardened steel) (2) Two 4x67 mm hardened steel inner suspension pins fit front or rear Replacement...
View full details
TRA9579R Traxxas Ring gear, differential/ pinion gear, differential (machined) (front or rear)
This is an optional pack of four Traxxas Fender Extensions, intended for use with TRX-4 and TRX-6 Kits. Includes: (4) Fender extensions (24) 3x8...
View full details
Traxxas Body, Maxx V2 (clear, requires painting)/ window masks/ decal sheet (fits Maxx V2 with extended chassis (352mm wheelbase))
This is a set of two Traxxas Window Nets intended for the Unlimited Desert Racer. Note: Pictures are for illustrative purposes only, no vehicles ar...
View full details
Traxxas Hoss LED Light Set with Power Supply. This optional complete LED light kit allows you to add lights to the front and rear of your Traxxas ...
View full details
This is an optional Traxxas Rustler 4x4 and Slash 4x4 LCG Chassis Red Brace Kit. This heavy-duty chassis brace fits Slash 4X4 models equipped with...
View full details
This is a replacement Traxxas Front Bulkhead, and is intended for the Traxxas Rustler 4x4 and Slash 4x4 vehicles. Features: Factory Replacement Pa...
View full details
Driveshaft, center, 6061-T6 aluminum (green-anodized) Traxxas designed this one-piece driveshaft out of tough 6061-T6 aluminum to be both strong a...
View full details
Differential output yoke assembly, extreme heavy duty (2) (left or right, front or rear) (assembled with external-splined half shaft)/ screw pin (...
View full details
